Search found 13 matches

Go to advanced search

by Morris
Fri May 19, 2017 9:23 am
Forum: General Discussion
Topic: Need some help with wiring
Replies: 5
Views: 1746

Re: Need some help with wiring

Hi gannicus, The switch.. is it a cross/parallel switch? and witch of the coil's/rotor is switched? we are not stuck by Chinese wiring.. if you unscrew the mounting plate.. write down the color, or numbers of the wires.. and and check the position of those. determine the rotor, and field coil's.if n...
by Morris
Wed May 17, 2017 11:12 pm
Forum: General Discussion
Topic: Need some help with wiring
Replies: 5
Views: 1746

Re: Need some help with wiring

Hi gannicus, Aha, could you sort out witch one is the rotor , and witch one is the field coil? if so, you could wire the field and rotor in series.., so the magnetic field could only be reversed by switching positive and negative..no switching in the coil's are needed then. your setup now, is that y...
by Morris
Wed May 17, 2017 8:06 am
Forum: General Discussion
Topic: Need some help with wiring
Replies: 5
Views: 1746

Re: Need some help with wiring

Hi gannicus,

is your motor a 'seriemotor or a compound?

could you give me the exact spec's of you motor?.. e.g.type plate.. i can't read it well from the picture.

regards,

Tom
by Morris
Sat Mar 18, 2017 11:39 am
Forum: General Discussion
Topic: Can 2x60AHV-60VDC handles 48V?
Replies: 2
Views: 1495

Re: Can 2x60AHV-60VDC handles 48V?

hi gannicus,

i'm playing with a hv2x60a..and can tel you..your spec's is NO problem for the hv2x60a!!
If your working current is 20 amps per channel, use a 40 amp fuse, and set your board setting to 20 amps...it will go on for a lifetime...

best regards,

Tom
by Morris
Mon Mar 13, 2017 9:22 pm
Forum: General Discussion
Topic: S-bus receiver.
Replies: 2
Views: 1267

Re: S-bus receiver.

Thank you acidtech, no problem.
i was just wondering... ;)
by Morris
Fri Mar 10, 2017 8:23 pm
Forum: General Discussion
Topic: S-bus receiver.
Replies: 2
Views: 1267

S-bus receiver.

Hi guy's,

could anyone tell me if the possibility exist to connect a s-bus receiver to the roboclaw? e.g. 2 roboclaws controlled by an s-bus (R.C.)receiver..

t.y.

Tom
by Morris
Wed Feb 15, 2017 10:51 am
Forum: General Discussion
Topic: HV2x60a controller trips..
Replies: 13
Views: 4758

Re: HV2x60a controller trips..

Thank you!
by Morris
Mon Feb 13, 2017 10:19 pm
Forum: General Discussion
Topic: HV2x60a controller trips..
Replies: 13
Views: 4758

Re: HV2x60a controller trips..

support@ionmc.com already send me the new version for the HV2x60a.. (4.1.20)
is this also useable for the 2x30a? or is that a different Firmware ?

t.y.

Tom
by Morris
Fri Feb 10, 2017 8:30 am
Forum: General Discussion
Topic: HV2x60a controller trips..
Replies: 13
Views: 4758

Re: HV2x60a controller trips..

Can i use the new (4.1.20) firmware also for the 2x30a controller?
by Morris
Fri Feb 10, 2017 8:16 am
Forum: General Discussion
Topic: HV2x60a controller trips..
Replies: 13
Views: 4758

Re: HV2x60a controller trips..

Hi Acidtech, Nathan send me a link to the new firmware, i installed it..and guess.. it works pretty fine..running smooth and no erratic behavior at low rpm's.. :D :D i use all the standard settings the new firmware provided, and it seem's that it is the right thing...only the deceleration settings m...

Go to advanced search

cron